ASTM A860 PDF

adminComment(0)

This standard is issued under the fixed designation A/AM; the number 1 This specification is under the jurisdiction of ASTM Committee A01 on Steel. ASTM A/AM Direct No.: + Fax No.: + Email: [email protected] Board No.: + ASTM A_机械/仪表_工程科技_专业资料。Designation: A/AM – 10 Standard Speci?cation for Wrought High-Strength Ferritic Steel.


Astm A860 Pdf

Author:JERROLD ANGELICO
Language:English, French, Portuguese
Country:Montenegro
Genre:Fiction & Literature
Pages:452
Published (Last):10.11.2015
ISBN:238-1-24741-578-9
ePub File Size:25.87 MB
PDF File Size:17.60 MB
Distribution:Free* [*Sign up for free]
Downloads:33652
Uploaded by: RENAE

ASTM A - Download as PDF File .pdf), Text File .txt) or read online. A / AM Standard Specification for Wrought High-Strength Ferritic Steel Butt-Welding Standard + Redline PDF Bundle, 10, $, ADD TO CART. Download astm a am standard specification for wrought high strength ferritic steel butt welding fittings abtresdeorebgolf.ga ( KB) now. Fast and easy at.

No cracks shall be permitted. Other imperfections shall be treated in accordance with After the removal of any cracks, the tees shall be re-examined by the original method.

Acceptable tees shall be marked with the symbol PT or MT, as applicable, to indicate compliance. NDE personnel shall be quali? Heat Treatment 6. Fittings formed above the transformation temperature or upon which welding is performed, shall be cooled to below the lower critical temperature prior to heat treatment.

Fittings shall subsequently be heat treated by normalizing, quenching, and tempering or stress relieving in accordance with Speci? Chemical Composition 7.

The results shall conform to Table 1 for either heat or Speci? The chemical composition thus determined shall conform to Table 1.

The product analysis shall be the basis for rejection. A chemical analysis shall be performed on deposited weld metal for each heat of? The weld metal shall be deposited in accordance with the quali? The nickel content of the deposited weld metal shall not exceed 1. Notch Toughness Properties 8.

Related titles

The testing shall be performed as speci? Full size Charpy, V-notch specimens shall be used whenever possible. Small size specimens shall be used only when the material thickness does not permit full size specimens.

The impact specimens shall not be? All base metal specimens shall be removed with the axis of the specimens longitudinal to the direction of primary metal? Weld-metal specimens shall be specimens with the axis transverse to the weld seam.

Tensile Requirements 9. Only the ultimate tensile strength need meet the minimum requirement of Table 2. Hardness Requirements Dimensions Rectangular specimen for thickness less than 5? The chemical composition thus determined shall conform to Table 1.

Internal and external surfaces shall be examined when size permits accessibility. Fittings formed above the transformation temperature or upon which welding is performed. Section VIII. Section IX.

Popular Publishers

Other imperfections shall be treated in accordance with Section Notch Toughness Properties 8. Acceptable tees shall be marked with the symbol PT or MT. No cracks shall be permitted. Full size Charpy. Paragraph UW are complied with. V-notch specimens shall be used whenever possible. Heat Treatment 6.

Fittings shall subsequently be heat treated by normalizing. The nickel content of the deposited weld metal shall not exceed 1. The product analysis shall be the basis for rejection. Small size specimens shall be used only. Chemical Composition 7. Dimensions Standard round specimen. C These requirements are intended to minimize fracture initiation. The requirements are not intended to give assurance against fracture propagation. The wall thickness at all points shall be. Only the ultimate tensile strength need meet the minimum requirement of Table 2.

Cvenergy absorptionC. Tensile Requirements 9. Finish and Appearance MLS[mm] 25 [0. Hardness Requirements Weld-metal specimens shall be specimens with the axis transverse to the weld seam. Transverse-weld tensile strength shall be reported in ksi. Hydrostatic Test Product Marking In addition. Section 8 and Table 2.

Related Post: ASTM A1003 PDF

The bar coding system. Heat Treatment 6. Fittings formed above the transformation temperature or upon which welding is performed, shall be cooled to below the lower critical temperature prior to heat treatment.

Fittings shall subsequently be heat treated by normalizing, quenching, and tempering or stress relieving in accordance with Specication A Chemical Composition 7. The results shall conform to Table 1 for either heat or Specication A for product analysis limits as applicable. The chemical composition thus determined shall conform to Table 1. The product analysis shall be the basis for rejection.

For referee purposes, Methods, Practices, and Terminology A shall apply. This examination shall be performed in accordance with a written procedure and shall be performed after nal heat treatment.

Contact our suppliers

Only the side wall area of the tees need be examined. This area is dened by a circle that covers the area from the weld bevel of the branch outlet to the center line of the body or run. Internal and external surfaces shall be examined when size permits accessibility.

No cracks shall be permitted.

Re: ASTM A860 / A860M - 14 needed

Other imperfections shall be treated in accordance with Section After the removal of any cracks, the tees shall be re-examined by the original 2 7. A chemical analysis shall be performed on deposited weld metal for each heat of ller metal or, for submerged arc welding, each heat of ller metal and batch of ux. The weld metal shall be deposited in accordance with the qualied weld procedure. The nickel content of the deposited weld metal shall not exceed 1. Notch Toughness Properties 8.

The testing shall be performed in accordance with Test Methods and Denitions A Full size Charpy, V-notch specimens shall be used whenever possible.

Rectangular specimen for thickness less than in. Width of specimen in. Toughness: Cvenergy absorptionC; measured at 50F [46C]. Size, mm 10 7.

For each in. When the section thickness lies between two values dened above, the minimum elongation value is determined by the following equation: E 5 48t 1 PDF Pro is entirely online, there's no software to download.

Distributing your curated content through a newsletter is a great way to nurture and engage your email subscribers will developing your traffic and visibility. Only the side wall area of the tees need be examined. Jump to Page. Maxcsa pdf writer, Lmt datasheet pdf 1n, Naprapathic pdf, by stephen few pdf download pn 80 n pdf download zen 20c1dr d v2 pdf eDocPrinter PDF Pro: Only the ultimate tensile strength need meet the minimum requirement of Table 2. Within the text, the SI units are shown in brackets.

The chemical composition shall conform to Table 1. Thumbnails Document Outline Attachments. August 24,